Welcome to our websites!

How do wire connectors work? The most complete knowledge of wire connectors

What is a wire connector? how to use? The text will connect the world network to you.
Wire connectors are a very critical category of connectors and are suitable for connecting wires. Our daily life is inseparable from electricity, and the transmission of electricity cannot be separated from wire connectors. The quality of wire connectors is critical. What makes you say that? You may often see various disasters caused by wire safety accidents in news reports. In fact, some of them are due to overweight application wires. Especially in winter and summer, because the usage rate of electrical products is too high, the wires are overweight. Once the connector in the wire box is out of specification, the wire will not be loaded and it is very easy to lose power.
Although the wire connector is small, it plays a vital role in power circuit engineering projects. The light wire world network will introduce you to the corresponding professional knowledge of wire connectors in detail:
【Wire connector raw materials】
1. Insulation layer material (chassis): polyester 66 (anti-leakage current penetration, ductility, stiffness, corrosion resistance, environmental protection, no halogen bulbs and indoor formaldehyde). temperature -35°C-105°C).
2. Raw material of pressure spring: steel (cold punching die (the punching die installed on the pressure testing machine) has high machining accuracy and no burrs. Repeated use can maintain ductility, compressive strength and corrosion resistance, and improve the power transmission line. wear resistance).
3. Touch raw materials: thickened electrolytic nickel + electroplated tin (good conductivity, good heat transfer, good plasticity, good corrosion resistance, avoid hot touch).
4. Contact surface coating: electroplated tin (corrosion resistance, not easy to air oxidation, good sealing).
[Wire connector solution]:
1. Bundling of wire insulation layer: The effective method is to first twist and then tin tin, and then bundle with high-toughness insulating tape.
2. Crimping cap wiring method: The second standard wire wiring method is the crimping cap wiring method. This method is the safest, most standardized, and the best way to connect wires.
3. The way of using the junction box: the junction box. Only one power line is allowed to be connected in the junction post. Reminder guys, every wire needs to be run through for maintenance.
[Application method of wire connector]:
The operation method of the wire connector is relatively simple. We disengage the cable sheath of about 10mm according to the correction length, then extend the actual operation lever, put the wire into the connector, and release the actual operation lever. Compared with the connection method of electrical tape, connecting wires with connectors is more reliable, and the actual operation is simpler and more convenient. It has the advantages of flame retardancy, compression resistance, insulating layer, convenient use, firm connection, instant current flow, strong practicability, and long service life.
When doing plumbing in a room, the wires usually run on the walls; however, when we run the wiring in the dining room kitchen and shower room, the power circuit is best run on the wall and the top. The suspended ceiling of the shower room, dining room and kitchen must not be slotted. We installed the power circuit on the roof and then covered it with a drop ceiling. When slotting the power supply circuit, be careful not to slot the load-bearing beam; when slotting the wall, slot it vertically. If it is necessary to make a vertical slot on the wall, the length of the horizontal slot should not exceed 30cm.
During water and electricity renovation, there must be no connectors in the electrical conduit. If wire connection is necessary, it can be carried out in the junction box. Strong electricity and weak electricity are different from electrical conduits. Separate the wiring and maintain a 500mm spacing to prevent the interference signal of the weak current to the weak current installation. When laying out the power circuit, the application of electrical products should also be considered, and the route volume should be appropriately increased; some socket switches should be pre-buried to prevent insufficient power sockets for household appliances in the future.
The above is the relevant information and operation method of the wire connector. In particular, everyone in the connector field needs to master the products in the field, so that when negotiating orders, they will also have sufficient professional knowledge of commercial services, leaving a good impression on people. In addition, wire connectors also play a vital role in people’s lives. If there are safety hazards such as power outages, you can also roughly infer. Thanks for reading the article.
In order to better benefit beginners in choosing good friends, we will help you quickly understand your job responsibilities, take up positions immediately, get promotions and raise your salary to achieve the peak of life. Inserting into the world must diligently sort out a set of buying secrets for beginners. If you want to train this professional skill, you must train first. . personal information me. In the purchase secret, there is a ten-year purchase card, about any problems and solutions encountered in the connector purchase. Hopefully, buying a good friend doesn’t have to be hard work. Reckless should also use skill!


Post time: Apr-09-2022